HI could you please email me the users manual of Fisher & Paykel Best thing about this new service is that you are never placed on hold and. Download Manual for Model DD FISHER & PAYKEL DISHWASHER. Sears PartsDirect has parts, manuals & part diagrams for all types of repair. User manuals for all our Fisher & Paykel appliances.
|Published (Last):||16 January 2004|
|PDF File Size:||17.59 Mb|
|ePub File Size:||4.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
Manual March Changes: Addition of info on Dry Enhancement Mode — refer section 4.
Dimensions and Specifications updated p 9, March Manual 1. When servicing the DishDrawer, Health and Safety issues must be considered at all times. Specific safety issues are listed below with their appropriate icon. These are illustrated throughout the service information to remind service people of the Health and Safety issues. March Manual 2. The joinery finished drawer front is supplied by the customer. March Manual 3.
They are capacitive touch switches and are supplied with an analogue signal from the controller that will change in the presence of an earthed mass i. March Manual Filling 3. From the connection to the water supply in the kitchen, the inlet hose enters the cabinet of the dishwasher at the base, onto a dual water valve.
It is not used for drying. The temperature is maintained by the thermistor. If a failure occurs with the electronic control of the heater plate, overheat protection is effected by a thermal fuse on the heater plate itself. March Manual The fan runs continuously during the drying cycle and will restart if the tub is opened and closed again. After the wash program is complete, the lid drives up, and the fan continues to run for 30 minutes, but will not restart if the tub is opened.
March Manual 4. Once the desired setting has been achieved push Power to exit.
FISHER & PAYKEL DISHDRAWER DD SERVICE MANUAL Pdf Download.
Selection of a setting affects how the Electronic Controller diverts supply water, how much water is treated, and how much salt is used mabual regeneration, in a manner that optimises the performance of the Water Softener.
March Manual 5. The following table details the display order of the test. March Manual The lid is lifted The display counts down to zero throughout this cycle The DishDrawer turns off at the end of this cycle.
March Manual 6. March Manual Fast Test Cycle: A fatal fault will usually require the assistance of a qualified service person, while a U1 user fault indicates the machine had failed to prime within a certain length of time usually because the tap has not been turned on.
To read a fault code off an integrated model, or prefinished products after MEM, refer to the LED Display column on the chart below. The LED that has activated on the secondary display indicates which fault code has occurred.
Answer each question with a yes or no and follow the instructions inside the relevant box. F1 The flood switch has been activated for more than 6 seconds Question Is there a F1 on both displays? Free jammed rotor, check for Go to Question 2 foreign object damage to rotor and rotor housing.
Fisher & Paykel DishDrawer DD603 Service Manual
Does the stator wiring from the Go to Question 3 Replace wiring harness or repair controller test okay? March Manual F4 No temperature increase has been sensed while the element is turned on Question Does the element heat in diagnostics?
Go to Question 7 Go to Question 2 Test the resistance of the heater Go to Question 3 Go to Question 5 element using the connection on the controller, is it correct? March Manual U1 DishDrawer failed to prime with water within approx. Go to Question 2 Turn the tap on Is the spray arm in place? To remove these stains requires a stronger concentration of detergent in the water.
More detergent is also required in hard water areas as minerals in the hard water reduce the effectiveness of the detergent. Drawer Front Removal 9. Push the right-hand end of the handle to the left until it feels free then remove it out towards you. March Manual Detergent Dispenser 9. Push back locking tabs to allow connectors to release. March Manual Filter Plate Removal 9. March Manual 9. Repeat for the left-hand side. For top tub lid actuators the bottom tub must also be removed to gain access to the lid actuator wiring harness.
The lower plastic chassis trim must be removed as per instructions in 9. Release the locking tabs for the connectors with a blade screwdriver while doing this.
This is to prevent damaging the locating tab at the front of each yoke which fits into the trim. Page of 47 Go. Table of Contents Add to my manuals Add. Page 3 Manual March Changes: Technical Overview The joinery finished drawer front is supplied by the customer. Touch Switches March Manual 3. Filling March Manual Filling 3. Overheat Protection March Manual 3. Water Softener where Fitted March Manual The fan runs continuously during the drying cycle and will restart if the tub is opened and closed again.
Page 23 March Manual The lid is lifted The display counts down to zero throughout this cycle The DishDrawer turns off at the end of this cycle. Page 30 March Manual F4 No temperature increase has been sensed while the element is turned on Question Does the element heat in diagnostics?
Tub Disconnection March Manual 9. Page 41 March Manual 9. Lid Removal March Manual 9. Lid Actuator Removal March Manual 9.
Fisher and Paykel DD603 service manual
Slide Rail Replacement March Manual 9. Water Valve Removal March Manual 9. Toe Kick Removal March Manual 9. Front Trim Replacement 9. Visher-paykel manual also for: Dishdrawer ddh dishdrawer ddi Dishdrawer ddih Dishdrawer ds Dishdrawer dsh Ddi Dishdrawer fisherr-paykel Comments to this Manuals Your Name.
Enter text from picture: I was trying to get the computer to reset. RE my comments re serivce DD Having the power and water supplies off for an hour and then restoring them does not fix the problem.
What else can I do? I am a degrees appliance engineer. By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?